Screws hold best when they go into the wood studs behind drywall. Where a screw can't reach a stud, a wall anchor gives it a grip in the drywall itself. Here's how to find studs, choose between studs and anchors, read an anchor's rating and mount a rack step by step.
What you'll need
Every Massello rack comes with screws, wall anchors and printed instructions, so no brackets are required. Shelf racks also include an Allen wrench. Bring:
- a drill and a screwdriver
- a stud finder, a tape measure, a pencil and a level
- safety glasses
Step 1: Find the studs
A stud finder is the most reliable tool for the job, This Old House notes. Slide it slowly across the wall, mark both edges of each stud, then mark the center between them. Studs are about 1.5 in wide and usually 16 in apart, center to center, sometimes 24 in.
No stud finder? This Old House offers a few clues. Outlets and light switches are almost always attached to the side of a stud, and the nail holes in baseboards often mark studs too. Knocking helps: the sound turns higher as you near a stud. A strong magnet will stick to the nails or screws that hold the drywall to the studs. To confirm a spot, lightly tap a finish nail into the wall just above the baseboard; if it meets resistance, there's a stud.
Stud finders can be fooled by pipes or metal, so check that the studs on either side sit 16 or 24 in away.
Step 2: Studs, anchors or both
If a screw goes into a stud, it doesn't need an anchor. Where there's no stud, use one.
On our Regular and Shelf racks, the screw holes are 7.5 in apart on the 4-hook size, 12 in on the 6-hook, 16.5 in on the 8-hook, 20.5 in on the 10-hook and 25 in on the 12-hook. On Irregular racks, measure between the holes on your rack.
- Hole spacing close to your stud spacing? Each screw may reach a stud. The 8-hook rack's 16.5 in, for example, is close to the common 16 in. Check every mark with the stud finder before drilling.
- Only one hole lines up? Put that screw into the stud and use anchors for the rest.
- No stud where you need one, or you'd rather center the rack? Hang it without studs: use anchors for every hole and place the rack exactly where you want it.
Step 3: Mark, level, drill and mount

- Unbox the rack, lay out the hardware and rest the rack safely on the floor.
- Choose your height and pencil-mark each screw point. Use a level to make sure the rack will hang straight.
- Check for wires and pipes before you drill (see the safety notes below).
- Drill at the marks. For an anchor, the hole should match the anchor's body so it fits snugly; for a screw going into a stud, a smaller pilot hole is enough.
- Press the anchors firmly into the holes until they sit flush with the wall. A gentle tap with a hammer helps.
- Line up the rack's pre-drilled holes with the anchors.
- Drive in the screws and tighten until the rack is secure. Stop once it's snug: overtightening can damage the drywall and loosen the hold.
- Snap on the screw covers for a seamless finish.
- For a Shelf rack, seat the shelf on top and tighten its short screws with the included Allen wrench.
How much weight can drywall anchors hold?
There's no single number. It depends on the type of anchor, the thickness and condition of the wall, and the direction of the load. Makers rate anchors for shear (a load along the face of the wall, like weight pulling down) and tension (a load pulling straight out). Plastic expansion anchors are the lightest duty, toggle bolts hold the most and molly bolts fall in between, according to Fine Homebuilding.
To read a rating:
- Use the maker's number. It isn't always printed on the package, so check the maker's website too.
- Check what kind of number it is. Some makers list an ultimate load, the point at which the anchor failed in lab tests, and note that industry safety standards recommend using only a quarter of it. Others already build in a safety margin. This Old House puts it simply: choose anchors that can hold four times what you're hanging.
- Remember leverage. Anchor makers note that weight held farther from the wall strains an anchor more than the same weight held close to it. Our open hooks reach 4 to 4.5 in from the wall.
Our maker rates each hook at 6 to 8 lb (2.7 to 3.6 kg). How firmly the whole rack holds also depends on the wall and what the screws go into, which is why a stud comes first wherever one lines up. If you choose your own anchors, pick a type made for your wall and stay within its maker's rating.
Plaster and brick walls
Plaster is generally stronger than drywall but more prone to cracking, This Old House notes. Find the studs first, put masking tape over each spot and drill slowly with a carbide bit, as Hunker advises.
Brick calls for a masonry bit, best in a hammer drill. This Old House and Bob Vila both favor drilling into the brick itself rather than the mortar for anything but light items, and This Old House advises staying more than an inch from any edge. Use anchors made for masonry and follow their maker's directions for hole depth and load.
Safety notes
- Wires and pipes can run close to studs or even be attached to them. Cable usually runs up from a light switch, and it can reach an outlet from any direction, so take extra care near both. Some stud finders also detect live wires.
- Wear safety glasses when you drill. For plaster or brick, add a dust mask; Bob Vila recommends an N95 respirator for brick dust.
- Before you load the rack, make sure it feels solid on the wall, and keep each hook within its 6 to 8 lb rating.
- Not sure about your wall? Ask a professional before you drill.
These steps cover our Regular Piano Coat Rack, Irregular Piano Coat Rack and Piano Coat Rack with Shelf alike, and our FAQ and Size & Care Guide have more answers.